Saskatoon
Saskatoon
306-500-7778 PolarTechSprayFoam@shaw.ca 12 Bay 5 – 2949 Miners Ave. Saskatoon, SK. S7K 4Z6
CCMC Listed
# 14133-L
Certified
CUFCA Applicators
Number #1
In Customer Satisfaction.
Get A Quote

The Various Spray Foam Insulation Problems That You Must Avoid

Before deciding to put spray foam insulation in your home, some considerations should be made. We’ll go over some of the most typical issues and installation blunders that crop up when spray foam insulation is done improperly or by someone without sufficient knowledge, as well as why it’s crucial for spray foam insulation installers to be properly licensed and trained.

1. There Are Air Leaks in Your Home

There may have been a mistake during the spray foam insulation installation if you are still experiencing air leakage after having it done recently. The insulation was probably not mixed properly, causing this. There is a risk that the spray foam won’t expand to its full size and seal any leaks.

The purpose of spray polyurethane foam is to expand and form a seal against the air. During the frigid winter months, this helps to keep the outside air out and the interior warm. Energy expenditures could soar if the building is not adequately sealed.

2. The Installer Used Either Too Little or Too Much

Both closed-cell and open-cell spray foams require a specific layer thickness for optimal performance, thermal efficiency, and insulation.

It’s possible to end up with expensive energy bills and an unpleasant home if the spray foam or closed-cell foam insulation isn’t thick enough to accomplish its job. Insulation thickness must be checked with a professional insulation contractor to ensure compliance.

3. There Is a Separation between the Spray Foam and the Frame

Insulation spray foam may separate from the frame if not mixed properly. When properly mixed, the chemical reaction of spray foam causes it to expand and remain in the enclosed cavities where it is applied. Incorrect chemical mixing during installation might cause spray foam to separate from the wall. This is both risky and inconvenient.

4. The Spray Foam was Applied Too Hastily by the Installer

Too much haste during the foam insulation installation could lead to missing areas. The insulation material needs to be strategically applied so that it can grow to its full potential.

Foams can be categorized by their density and rigidity, with open-cell foam being more lightweight and flexible. For this reason, it’s crucial to pay attention to both the rate and volume of the spraying. A trained professional specializing in spray foam insulation will be familiar with all the necessary material installation procedures.

5. There Is an Odour and Off-Gassing from the Spray Foam

When compared to common insulations like fibreglass, spray foam allows for more odour and off-gassing during installation. The impacts of this should not linger beyond the first few hours following installation. If your open-cell or closed-cell insulation was built incorrectly, it could be causing health problems like skin and eye irritation or breathing difficulties.

A well-informed and licensed contractor will install high-quality ventilation to ensure this. Doing so helps neutralize any off-gassing or unpleasant odours. The area in an attic, for instance, may be somewhat congested. Consequently, good airflow is crucial for a successful roof insulation installation. A trained expert will be able to set air exchange units there to help alleviate the problems.

Insulation Installation: Why You Should Call a Pro

In reality, there are a variety of benefits to having a professional handle the installation of your home’s insulation. Specialist contractors in this industry will be able to spot any issues with the setup. In the long run, the key to preventing things from getting worse is seeing little flaws before they escalate.

Irritators in the air or a rising energy bill are two potential outcomes of subpar insulation. Either way, these issues are likely to arise quickly if you attempt to install your own insulation without following the necessary procedures.

Conclusion

Indeed, spray foam insulation can be a great way to keep your home or building comfortable and energy efficient. However, it is important to be aware of the potential problems that could arise. Poor installation, failure to follow product instructions, or using the wrong product can cause problems with the insulation.

By understanding the potential problems and following the manufacturer’s instructions, you can ensure the best results when it comes to spray foam insulation.

If you are looking for a company in Saskatoon that provides spray foam insulation services, look no further than our expertise here at PolarTech Spray Foam. Our company provides a wide range of insulation installation and removal services. Call us today and let us handle all your spray foam insulation needs in no time.

About the author

Leave a Reply

Text Widget

Nulla vitae elit libero, a pharetra augue. Nulla vitae elit libero, a pharetra augue. Nulla vitae elit libero, a pharetra augue. Donec sed odio dui. Etiam porta sem malesuada.

Recent Works